LEK2SB-PTC1，LEK2SB-KTC1，LE12SB-PTC1，LE12SB-kTC1，LE33SB-pTC1，LE33SB-kTC1，LEF4SB-pTC1，LEF4SB-kTC1，LEH4SB-PTC1，
LEH4SB-kTC1，LE34SB-pTC1，LE34SB-kTC1，LEG4SB-pTC1，LEG4SB-kTC1，lek5Sb-pTC3，LEK5SB-KTC3，LEH5SB-PTC3，LEH5SB-KTC3，

LE03SB-PTC1，LE03SB-KTC1， LEK3SB-PTC1，LEK3SB-KTC1，LE44SB-PTC1，LE44SB-KTC1，LEG5SB-PTC3，LEG5SB-KTC3，LEH6SB-PTC3 ，

LEH6SB-KTC3，LEK7SB-PTC3，LEK7SB-KTC3，LEH7SB-PTC3，LEH7SB-KTC3，LVH7SB-WTSK*，LEJ8S2-PTCB* ，LEH8SB-PTCB*

LPK2EB-PTC1,LPK2EB-KTC1,LPB2EB-PTC1,LPB2EB-KTC1,LPD3EB-PTC1.LPD3EB-KTC1,LPF4EB-PTC1,LPF4EB-KTC1,LPH4EB-PTC1,LPH4EB-KTC1,
LPD4EB-PTC1,LPD4EB-KTC1,LPG4EB-PTC1,LPG4EB-KTC1,LPK5EB-PTC3,LPK5EB-KTC3,LPH5EB-PTC3,LPH5EB-KTC3,LPA3EB-PTC1,LPA3EB-KTC1,
LPK3EB-PTC1,LPK3EB-KTC1,LPB4EB-PTC1,LPB4EB-KTC1,LPE4EB-PTC3,LPE4EB-KTC3,LPG5EB-PTC3,LPG5EB-KTC3,LPH6EB-PTC3,LPH6EB-KTC3,
LPK7EB-PTC3,LPK7EB-KTC3,LPH7EB-PTC3,LPH7EB-KTC3,LVH7EB-WTSK*,LPJ8EB-PTCB*,LPH8EB-PTCB*

?所有型號標配: 三功能閥,注射閥, 底閥, 進出口軟管（標*的型號無三功能閥） ?電源:220V*大功率:300W
?配五功能閥需單獨訂貨
?PVC泵頭可選，價格與PVDF泵頭材質相同.

? - 電擊危險。本泵配備的電源插頭為三腳接地型。要減少電擊危險，只可連接到已正確接地的接地型插座。
? 計量泵連接的電源必須與泵的數據標簽上的電源-致「如果施加的電壓高 于泵的額定值，則會損壞內部電路。
? 在:控制裝置的電子電路中，通過過電壓吸收元件和高壓半導體來測量沖擊 電壓。盡管如此，過量的沖擊電壓可能在某些區域中導致故障。因此，不 可與產生高壓的重型電氣設備共用一個插座。但是，如果必須共用一個插 座，則應采取措施，（a）在:泵的電源連接上安裝過電壓吸收元件（可變電 阻，波沖電阻*小2000A），或lb）安裝噪聲抑制變壓器
5.3.3 控制程序（續）
例子 選定型號 =LPD4
設置行程長度 =100%
設置行程速率 = 100%
輸出丨容量 = 21 加侖/天（GPD） *
（額定壓力）
要求流量 = 15 GPD
調節行程速率到80%
輸出容量 = 0.80 x 21 = 16.8 GPD*
行程長度設定值= 丄x 100 = 90%）（約）
16.8
由此來求得要求的流量，行程長度設置為90%，行程速率設置為80%，即輸出容量 =
0.90 x 0.80 x 21 = 15.12 GPD*。

PULSAtron Series E Plus Metering Pump

General Description
Pulsafeeder PULSAtron Series E Plus chemical metering pumps are positive displacement, diaphragm type pumps. Output volume is adjustable while pumps are in operation from zero to maximum capacity. The PULSAtron Series E Plus contains a highly reliable timing circuit as well as circuit protection against voltage and current upsets. This pump features solenoid protection by thermal overload with auto-reset. The Series E Plus guided check valves, with their state-of-the-art seat and ball designs, provide precise seating, and excellent priming and suction lift characteristics. Our timing circuit is highly reliable and, by design, virtually unaffected by temperature, EMI and other electrical disturbances.
Pump Controls
Adjustment is by means of readily accessible dial knobs, one for changing stroke length and the other for changing stroke frequency. Both knobs are located opposite the liquid handling end. Automatic control via 4-20mA DC and stop function inputs. Auto-Off-Manual switch.
Drive Assembly
The pump drive is totally enclosed with no exposed moving parts. Electronics are housed in chemical resistant enclosure at the rear of the pump for maximum protection against chemical spillage. Average electrical power consumption is 130 Watts.
Materials of Construction
See Specifications tab. Chemical metering pump housing shall be of chemically resistant PBT thermoplastic. All exposed fasteners are stainless steel. Valve seat and seal ring are renewable by replacing the cartridge valve assembly.

Pulsafeeder PULSAtron Series E Plus Chemical Metering Pump - Key Features

• Manual Control by on-line adjustable stroke rate and stroke length.
• Highly Reliable timing circuit.
• Circuit Protection against voltage and current upsets.
• Panel Mounted Fuse.
• Solenoid Protection by thermal overload with auto-reset.
• Water Resistant, for outdoor and indoor applications.
• Indicator Lights, panel mounted.
• Guided Ball Check Valve Systems, to reduce back flow and enhance outstanding priming characteristics.
• Few Moving Parts and Wall Mountable.
• Safe & Easy Priming with durable leak-free bleed valve assembly (standard).
• Reliable metering performance.
• Rated "hot" for continuous duty.
• Leak-free, sealless, liquid end.

Includes:

A weighted foot valve/strainer assembly, a 1/2" NPT male injection fitting/back pressure check valve assembly, 4' suction tubing, 8' discharge tubing and Owners Manual